Rega Planar 25 User Manual download pdf

**IMPORTANT**

PLEASE READ THIS INFORMATION THOROUGHLY BEFORE

STARTING WORK.THIS MOTOR CHANGE SHOULD ONLY BE

CARRIED OUT IF YOU ARE TECHNICALLY QUALIFIED.

Thank you for purchasing this Rega upgrade product. This kit is designed to

fit all past models of Rega turntables that do not already use a 24v motor.

Please read these instructions carefully before fitting to ensure you use the

correct kit parts for your model turntable.

WARNING: DISCONNECT YOUR TURNTABLE FROM THE

MAINS ELECTRICITY BEFORE ATTEMPTING FITTING.

Before starting work pre fitting preparation and advice.

With the platter and drive belt removed place some adhesive tape across

the hub bearing assembly (which the platter sits on) sticking it to the plinth.

This will prevent the hub falling out ensuring the ball bearing remains in

place and that no oil is lost when the turntable is upside down during fitment.

Make sure the arm is securely in the arm clip and the stylus guard is fitted to

your cartridge to ensure no damage occurs. Support the turntable on a

cushioned surface to ensure no unnecessary pressure is exerted on the

tonearm bearings.

Stage 1 : Removal of old motor.

On the underside of the turntable remove the two black screws holding the

plastic motor cover tray in place. Once removed you should remove the

single screw which holds the old motor PCB in position. You are now ready

to de-solder and remove the existing mains lead brown & blue (230v) or

Black (115v). Then de-solder the two switch wires. (usually white and white

with a black stripe).

The old mains lead is no longer required once de-soldered, completely

remove it from the turntable. The black grommet which held the lead in the

plinth place should be removed from the lead and refitted in the mains lead

hole on the rear of the turntable. If your turntable uses a plastic motor PCB

tray and lead clamp, this should also be removed.

You are now ready to remove the old motor and PCB - Early Rega

turntables will exhibit two mounting variations. Early Planar and Planet

models were suspended on ‘O’ rings and fitted via 2 screws (often plastic)

on the top of the plinth, simply undo the two screws which will allow the

motor to be removed.

Most other models use an adhesive pad to hard mount the motor similar to

the method used in this upgrade kit. To prevent damage to the plinth great

care must be taken when removing the old pad. Do not try to lever out the

motor from a single point in one go. Use a wide flat blade screwdriver and

gradually ease the pad away from the plinth at various points until the

pad gives way. With the motor removed ensure any excess pad left inside

the plinth is removed and the surface is left clean and flat.

Stage 2 : Installing the new motor

To ensure correct pulley height you must carefully follow the instructions

relating to the turntable model you are fitting the kit to. The pulley is factory

fitted to a set height. Correct mounting height is achieved between models

by using a different thickness motor mount pads either Thin (double) or

Thick (triple) both supplied. Check your turntable model against the pad

requirement chart below. Some variations may occur across the range

therefore it is highly recommended to visually double check the belt will sit

correctly on the sub platter on both 33 and 45 before removing the sticky

backing and applying the motor as shown below.

NB. **A spare hub washer is included which can be fitted to the top side of

the brass hub bearing. This will allow extra height adjustment in case of

minor variations on Planar models. In most cases this will not be necessary.

With the correct pad depth selected remove one side of the protective film

and place into the motor cavity (fig 2). line up the centre of the pad with the

hole in the plinth as close as possible. Press firmly across the entire

surface of the pad to ensure good adhesion. Before fitting the motor you

must make sure the MOTOR AND WIRING is fed THROUGH the centre of

the PCB to avoid the wires being trapped by the PCB when fitted.

Remove the protective film from the top of the fitted motor pad and carefully

line up the motor to match the shape of the pad to maximise adhesion. The

label on the motor is orientated correctly, if you can read the label the

motor wiring is automatically dressed in the correct position (avoiding

contact with the motor body).

DO NOT PRESS THE MOTOR FIRMLY

AT THIS STAGE. Turn the deck over to

ensure the pulley is central in the plinth

hole. If it is not central (and you have not

already pressed the motor firmly) you may

be able to realign the motor. (Spare pads

are available from your Rega dealer if

required). If you are happy with the position

of the pulley you can now push the motor

firmly onto the pad by applying even

pressure across the back of the motor. NB

early Planet and Planar models have thin

laminate, care should be taken not to push

too hard to avoid damaging the plinth on

these models, ideally support the plinth

with your hand from the underside when

applying pressure). Two black circular

stickers are supplied to cover the holes

where the older suspended motor was

removed.

Stage 3. Reconnect the Switch Wire (fig 3).

You can now reconnect the switch wires to the position marked SW on the

PCB. (These can be connected either way as it is a non-polarity

configuration). Again it is important to make sure the switch wires are

dressed correctly THROUGH the PCB not around the outside. Snip off the

excess on the underside to prevent the risk of a short. Once complete the

assembly should appear as fig 4. Inside the motor cover tray a single white

circular sticker is fitted which will align with the back of the motor bias pad.

When the supplied tray is fitted it will gently compress. (On Planar 3 Planar

25 and Planet turntables add the supplied thicker circular pad to account for

the deeper plinth). There is no need to screw the new PCB into the plinth cut

out. The PCB is held in place with the supplied screws that hold the new

motor cover tray.

To connect your turntable use only the supplied wall plug power supply

directly into the jack socket on the back of the new cover tray. (fig 5. A) The

Secondary input (fig 5. B) is for connection of the Rega TT PSU which offers

electronic speed change and even greater noise reduction and stability.

(sold separately). WARNING: Socket A and Socket B should never be

connected simultaneously, when using the TT-PSU the power supply

plug supplied with this kit is no longer required.

24 v High Performance Synchronous

Motor Upgrade Fitting Instructions

Turntable model Pad requirement

Planet / Planar 3 / P3 2000 Planar 25 Thick - Triple pad required

RP1 / P1 / P2 2000/ Planar 2 Thin - double pad required

fig 2.

Check Pulley height for

correct alignment.

If the pulley is too high it

may contact the platter.

If it is too low the belt

will fall off the sub

platter on 45rpm.

Correct pulley height Sub platter

Check both 33 and 45 belt positions.

fig 1.

Thin (twin) pad shown. Ensure surface is

clean before fitment.

Correct orientation of pad in plinth.

Switch wires

fig 3.

Motor orientation & wiring

correctly dressed. Not

contacting the motor body.

fig 4.

fig 5.

Motor Bias Pad.

fig 4.

Position of spare hub washer

**Only if required

**IMPORTANT** 1

Summary of Contents

Page 1 - **IMPORTANT**

**IMPORTANT** PLEASE READ THIS INFORMATION THOROUGHLY BEFORE STARTING WORK.THIS MOTOR CHANGE SHOULD ONLY BE CARRIED OUT IF YOU ARE TECHNICALLY QUALIF

Comments to this Manuals

No comments

Rega Planar 25 User Manual

Browse online or download User Manual for Turntable Rega Planar 25. 24V Motor Upgrade Kit -- English

Summary of Contents

Comments to this Manuals

Related products and manuals for Turntable Rega Planar 25